RAID is a technology that combines two or more disk arrays into logical units, so it behaves as a single drive to provide benefits such as improved performance, better fault tolerance, and enhanced reliability. This grouping can be implemented through hardware or software. These disks can be grouped in many types of configurations called RAID levels. Some of the popular types are RAID 0, RAID 1, RAID 5, RAID 6, and RAID10. Each of these RAID levels is designed to achieve a specific goal. In this article, let’s take a look at the differences between RAID 0 and RAID 1, their benefits, shortcomings, and which works well in different situations.
Also called disk striping, this configuration divides data across different disks, so the read-write can happen simultaneously across multiple disks and, in the process, improve its overall speed. Here, a stripe is the data that is divided across multiple disks while a striped unit is the data available on a single drive. This striping can happen in many ways. For example, let’s say we have 10 hard disks and 32MB of data that has to be striped across the different disks. Some systems might stripe 1KB of data from disk 1 to 10 and then start all over again while others could stripe data through the odd numbers first and the even numbers next. It depends on whether the striping happens at the byte, block, or partition levels.
The advantages of RAID 0 are:
- Improved performance: When data is striped across four drives, it provides four times more bandwidth. If we assume that each drive runs at about 250 Input Output Operations per Second (IOPS), this setup will have 1000 IOPS, thereby making it super-fast for users.
- No overhead: Since RAID 0 doesn’t use parity, there’s no overhead, and the entire drive’s capacity is used for storing.
- Low cost: Among all RAID levels, this configuration costs the least and is supported by all RAID controllers.
- Easy to implement: There is nothing much to set up for RAID 0, and this makes it the easiest and quickest to implement.
The downside of RAID 0 is that it has no parity and hence no-fault tolerance. This means, if your data is corrupted or lost, there is no resiliency or back up, and it’s impossible to retrieve the lost data. This makes RAID 0 completely unsuitable for critical data.
Also called mirroring, this RAID level replicates data across two or more disks for better redundancy. This configuration requires a minimum of two drives, so data can be written to both simultaneously. This makes read operations fast as the data can be read from both the drives at the same time. However, write operations will be slower since the data has to be written to two disks.
- Data redundancy: The biggest advantage of RAID 1 is data redundancy, as data is replicated across two or more disks.
- Fault tolerance: This level is most-suited for mission-critical applications because when one drive fails, the other will automatically take over. Since both the drives contain identical data, there will be no impact to users.
- High availability: Since data is replicated across multiple disks, it will be available when needed, and the possibility of data loss is very negligent.
- High performance: Data can be read from two or more devices simultaneously, so it is fast.
- Reduced storage capacity: Since the same data has to be stored twice, your overall storage capacity is halved.
- No real-time swapping: When a disk goes down, the secondary disk doesn’t take over automatically. The system has to be restarted before the secondary disk takes over, and this can be a bit of an inconvenience.
- Expensive: This RAID level requires more space to implement, so it is more expensive when compared to RAID 0.
Now, let’s run through some real-life scenarios and the ideal RAID level for each.
High speed read and write
You have a situation where you want the read and write to be super quick, but the data is not so critical. This means, even if there is a data loss or corruption, it doesn’t affect your business as long as the read-write is quick.
The best example of this scenario is caching live stream video. Here, speed and performance take precedence over data loss and corruption, and for this scenario, RAID 0 is the best choice.
Your goal is to provide quick results to your users, so high-speed I/O is a must. At the same time, you’re not so worried about the loss of data as you have a master copy in another storage device that can be recovered easily when needed.
In this case, RAID 0 is the best choice.
Low disk space
If you have more data to store and run out of disk space, RAID 0 is a good choice as there are no overheads, and the entire disk space will be used for storing. That said, there’s no fault tolerance or backup either, so the data you want to store must be non-critical and shouldn’t impact your business even if it’s lost or corrupted.
When you want to store critical and sensitive data, RAID 1 is your best bet as it mirrors data on two disks, so even if there is a problem with the primary disk, you can always retrieve the content from the second one.
In general, RAID 1 is a good choice if data redundancy is a key feature of your storage needs.
It’s important to note that RAID 1 is not a backup option because when a corrupted data is sent from the operating system, it writes to both the drives, thereby corrupting both the drives.
Many gamers like to use RAID 0 because it is easy to set up and offers considerably faster speeds that, in turn, enhances their gaming experience. But some gamers don’t prefer using RAID 0 because of the possibility of data loss while many enjoy its increased throughput. It’s a personal choice between data safety and high speed.
If you have many users requesting the same content, a RAID 1 setup will work as it offers high speed reads. Since the same data is mirrored across different disks, the same content can be accessed faster when multiple users request for it simultaneously.
RAID 0 or RAID 1? It comes down to performance or data redundancy
RAID 0 and RAID 1 are two types of configurations or levels that can be set up with an array of independent disks. RAID 0 offers striping, which translates to better performance, but no-fault tolerance or data redundancy. RAID 1, on the other hand, offers mirroring, so the same data is available in two disks. RAID 1 is slightly slower than RAID 0 because there are two writes, but the read operations are equally fast.
Due to the above differences, these RAID levels work well in different scenarios. In general, when you need performance over data redundancy, RAID 0 is your choice, while RAID 1 is the choice when you’re handling mission-critical data where redundancy is a must.
We hope the above situations give you a better idea of where to use RAID 0 and RAID 1. For more on RAID levels, check the links below for other articles in this series. And do share with our readers the different situations where you have used the two levels we talked about in this article.
Featured image: Shutterstock
More RAID levels articles
- Hackers: the New Ghosts in the Machine
- RAID 5 vs. RAID 6: When to use each level and why
- RAID 10 vs. RAID 5: When to use each level and why
- RAID 1 vs. RAID 5: When to use each level and why
- Hardware RAID vs. software RAID: Pros and cons for each